The Master and Manager can also change the user codes by following the "Activate user codes" section steps 1 thru 3.ĭeleting user codesAlways perform this operation with the door open.ģ. Enter: New User Code - # - New User Code - #, before the orange light disappears. This will activate User Five (5).Īlways perform this operation with the door openģ. The lock will indicate an invalid code entry with a double signal and the old code is still valid.Įxample: # - Master Code or Manger Code - # - 5 - * - New User Code - # - New User Code - #.The lock will indicate a valid code entry with a single signal.If a mistake is made during the activation, wait thirty (30) seconds and repeat steps 1 thru 3. Enter: User ID Number (3-7) - * - New User Code - # - New User Code - #, before the orange light disappears. Enter: 2 - * - New Manger Code - # - New Manager Code - #, before the orange light disappears.ģ. Enter: # - Master Code or Manager Code - #ģ. The lock will indicate an invalid code change with a double signal and the old code is still valid.ġ.The lock will indicate a valid code change with a single signal.Test the new code several times before closing the door: Enter: * - Code - # If a mistake is made during the change, wait thirty (30) seconds and repeat steps 1 thru 3. Enter: 1 - * - New Master Code - # - New Master Code - #, before the orange light disappears. The set light will stay orange for ten (10) seconds.ģ. (Code length: 1 to 10 digit code) Always perform this operation with the door open.Ģ. During this shut down period you will not get a response from the keypad. If three incorrect entries are entered in a row, the keypad will shut down for a period of five minutes.You may also register your codes on our website at A single signal (LED flashes and beeps once) response from the lock indicates valid entry.Ī double signal (LED flashes and beeps twice) response from the lock indicates an invalid entry. Please keep your codes in a secure location. You should set the lock to your own unique master & manager code immediately. The SentrySafe electronic lock is shipped with a factory set master & manager code (777777). More information can be found in the attached document web page. : Entering the incorrect passcode 3 times will lock the system for 20 seconds. If the entered code is invalid the yellow light willįlash and the buzzer will quickly sound, this indicates the code needs to be re-entered. Each key pressed will be accompanied by a buzzer and a yellow flashing light. Turn the knob clockwise within 5 seconds to open the door.ģ. Input your code and then press the "B" button, the green light will turn on.Ģ. Immediately after entering your new code, press the "A" or "B" button on the keypad. New user passcodes may be 3-6 digits long.ģ. Press the red button, listen for a beep and then enter your new user passcode. Press the "0" button on the keypad twice. Open your safe with the passcode you wish to change and leave the door ajar.Ģ. SETTING UP OR CHANGING A MANAGER PASSCODEġ. This safe stores up to 2 passcodes (a user code and a manager code). Immediately after entering your new passcode, press the "A" or "B" button on the keypad. Immediately enter your new passcode (3-6 digits long)Ĥ. Press the red button and listen for the beep.ģ. With the door open, locate the red button on the back of the door near the hinge.Ģ. : If both the red and green lights are on while the safe is open, this indicates that the batteries are low and needġ. Install 4 AA batteries provided and replace the battery cover. Remove the battery cover plate located on the inside of the door.ģ. Remove the key plate cover, insert the key into the keypad and open the door.Ģ.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |